Polyester epoxy

carlp" (carlp@ic24.net) writes:

 > use of polyester for
 > the bulk of construction

could you be a little more specific?

 >.. and epoxy to seal the polyester

for an effective moisture seal 3 layers of epoxy are recommended.
epoxy does not flow like paint or varnish to leave a smooth finish.
,,,,,,,,,,,,,,,,,,,,,,,
Thanks for the reply,
The boat will be an heavy displacement type 45% Bal.
light frames 475mm spacing with stringers ply gusset floors continuing
down to form box type keel, a V bottom single slightly radius chine, 23ft
wl.
lined with foam and covered with varnished matchwood.
The hull 6mm ply, or 9mm on stringers and frames,depending on final
deciding factors, 6 mm ply 400 gm polyester and epoxy weave and finish ? .
9mm ply and single 125 gm weave with epoxy and finish epoxy gel ? paint ?.
Carl.<!-- ~MESSAGE_AFTER~ -->
 >> Stay informed about: Polyester epoxy 

If this is not a "troll", then read on:

I would have a problem with you mixing the two types of resins - I
wouldn't buy the boat. It's not because of the epoxy - I'm not
convinced that the poly should be next to the hull.

I have had great luck with epoxy staying stuck to wood. Not so with
poly - it's designed to stick to itself and fiberglass, and f/glass,
and itself. I've had delaminations occur on my tests in using poly to
stick f/g to a wood hull. It may take a few years to happen, but thats
why I wouldn't buy a used boat constructed that way.

It may work wonderfully for years, and I hope it will for you,
However, do a lot of reading on the chemistry and bonding
characteristics before you sacrifice sweat and wallet-padding.
It will be cheaper to build it only once (duh... but true).

I have spent *months* in the past going over it, and over it again, to
eventually "bite the bullet" and get epoxy, and so far am still glad.

litmus test:
If it's a boat to be proud of, its worth the epoxy.

If it's a boat to :
  try a new design - poly
  take care of for 20 years - epoxy
  beat up, and become a 'planter' in 4 years - poly.
  make a f/g mold for a one-off - poly
  annoy others with fumes - poly

- - -
Why not slap together a cheap-ply row boat, and test this out, first.

make itunder 8ft and you can build it out of 1 or 2 sheets of
plywood, ~4mm. Then glass it - the poly wont be all that much for one
gallon, thats the premise, here. Maybe buy the glass for both all at
once, n save a few bucks.



On Sat, 27 Sep 2003 23:43:21 +0100, "carlp" <carlp.DeleteThis@ic24.net> wrote:

 >Anyone have suggestions or problems resulting from the use of polyester for
 >the bulk of construction and epoxy to seal the polyester, say a 85 gm.glass
 >woven cloth impregnated with epoxy .
 >Only the cost saving would be large, considering the difference in the price
 >of the two resins.
 >I have started on the frames of a 23 ft. WL. sailboat, strong back is in
 >place.
 >cheers
 > Carl.
 ><!-- ~MESSAGE_AFTER~ -->
 >> Stay informed about: Polyester epoxy 

If this is not a "troll", then read on:

I would have a problem with you mixing the two types of resins - I
wouldn't buy the boat. It's not because of the epoxy - I'm not
convinced that the poly should be next to the hull.

I have had great luck with epoxy staying stuck to wood. Not so with
poly - it's designed to stick to itself and fiberglass, and f/glass,
and itself. I've had delaminations occur on my tests in using poly to
stick f/g to a wood hull. It may take a few years to happen, but thats
why I wouldn't buy a used boat constructed that way
''''''''''''''''''''''''''
All your points are what I have been pondering, I will stick to the original
plan of 9mm ply recommended as per plan and sheathed in epoxy impregnated
woven cloth.
You brought back the distant memory of unpleasant smells and nausea while
using polyester and the memories are not pleasant, mind you knowing what I
know now about fumes and fresh air flow, then we all thought we were
fortresses when we were young.
I am not a stranger to boat construction wood plastic steel, even a bit of
ferocement made up twin keels Iron blocks encapsulated with cement mix and
chickens wire, these lasted very nearly thirty years, with the boat in the
water for most of the year.
Carl.
 >> Stay informed about: Polyester epoxy 

Hey, Carl - good luck, good winds.

On Mon, 29 Sep 2003 11:38:28 +0100, "carlp" <carlp.TakeThisOut@ic24.net> wrote:


 >
 >I would have a problem with you mixing the two types of resins - I
 >wouldn't buy the boat. It's not because of the epoxy - I'm not
 >convinced that the poly should be next to the hull.
 >
 >I have had great luck with epoxy staying stuck to wood. Not so with
 >poly - it's designed to stick to itself and fiberglass, and f/glass,
 >and itself. I've had delaminations occur on my tests in using poly to
 >stick f/g to a wood hull. It may take a few years to happen, but thats
 >why I wouldn't buy a used boat constructed that way
 >''''''''''''''''''''''''''
 >All your points are what I have been pondering, I will stick to the original
 >plan of 9mm ply recommended as per plan and sheathed in epoxy impregnated
 >woven cloth.
 >You brought back the distant memory of unpleasant smells and nausea while
 >using polyester and the memories are not pleasant, mind you knowing what I
 >know now about fumes and fresh air flow, then we all thought we were
 >fortresses when we were young.
 >I am not a stranger to boat construction wood plastic steel, even a bit of
 >ferocement made up twin keels Iron blocks encapsulated with cement mix and
 >chickens wire, these lasted very nearly thirty years, with the boat in the
 >water for most of the year.
 >Carl.
 ><!-- ~MESSAGE_AFTER~ -->
 >> Stay informed about: Polyester epoxy 

So you are thinnking of using polyester to cover the exterior a
plywood hull.

Polyester is fine under certain conditions. Unfortunately the
conditons aren't generally known. There has been so much
advertising and hype surrounding epoxy, compared to polyester,
that there is not enough interest in finding out what the
conditions for using polyester are.

If you use polyester without knowing the conditions under which it
works you are taking a chance.

I owned an old mahogony strip 20 ft sailboat which had been
covered with polyester by the builder. The only place it gave
problems was at the centerboard slot where it came away from the
hull. I assume it was because of the stress on the hull at the
slot.

One way of saving money is to only cover the hull below the waterline in
epoxy, and paint the hull above the waterline. TF Jones does that with
plywood boats.

Another technique Jones has used is to make the bottom of the hull of
polyester and fibreglsss and the topsides of plywood. Its not to save
money but to get a bottom hull shape that can't be done in plywood panels.
However you could make the bottom panels of a plywood design of polyester
and fibreglass and the topsides of plywood. The fibreglass panels are made
on any good flat surface and put on the boat as if they were plywood panels.

I've not used epoxy to cover a hull but I've read it takes 3 layers to
waterproof the hull. See, for example, David Gerr's "Elements of Boat
Strength". Our local public libary has a copy.


--
------------------------------------------------------------------------------
William R Watt National Capital FreeNet Ottawa's free community network
homepage: www.ncf.ca/~ag384/top.htm
warning: non-freenet email must have "notspam" in subject or it's returned
 >> Stay informed about: Polyester epoxy 

Think of it this way:-
Polyester is a bonding resin, which means that it binds a material, I.E.
fibreglass by surrounding the fibres on both sides and through the fine
glass filaments. If you use it on ply then it cannot soak into the surface
and through to the other side to bind the plywood fibres.
Epoxy is basically a very strong glue which binds two surfaces together.
The costs will be negligible if you just put a lightweight coat of epoxy and
glass onto the hull, instead of coating it over a polyester surface.


"not-it.org" <anonymous DeleteThis @notmyaddress.org> wrote in message
news:8ilfnv8m4l8sqm2vrqvkepuq6t6cbjfo06@4ax.com...
 > If this is not a "troll", then read on:
 >
 > I would have a problem with you mixing the two types of resins - I
 > wouldn't buy the boat. It's not because of the epoxy - I'm not
 > convinced that the poly should be next to the hull.
 >
 > I have had great luck with epoxy staying stuck to wood. Not so with
 > poly - it's designed to stick to itself and fiberglass, and f/glass,
 > and itself. I've had delaminations occur on my tests in using poly to
 > stick f/g to a wood hull. It may take a few years to happen, but thats
 > why I wouldn't buy a used boat constructed that way.
 >
 > It may work wonderfully for years, and I hope it will for you,
 > However, do a lot of reading on the chemistry and bonding
 > characteristics before you sacrifice sweat and wallet-padding.
 > It will be cheaper to build it only once (duh... but true).
 >
 > I have spent *months* in the past going over it, and over it again, to
 > eventually "bite the bullet" and get epoxy, and so far am still glad.
 >
 > litmus test:
 > If it's a boat to be proud of, its worth the epoxy.
 >
 > If it's a boat to :
 > try a new design - poly
 > take care of for 20 years - epoxy
 > beat up, and become a 'planter' in 4 years - poly.
 > make a f/g mold for a one-off - poly
 > annoy others with fumes - poly
 >
 > - - -
 > Why not slap together a cheap-ply row boat, and test this out, first.
 >
 > make itunder 8ft and you can build it out of 1 or 2 sheets of
 > plywood, ~4mm. Then glass it - the poly wont be all that much for one
 > gallon, thats the premise, here. Maybe buy the glass for both all at
 > once, n save a few bucks.
 >
 >
 >
 > On Sat, 27 Sep 2003 23:43:21 +0100, "carlp" <carlp DeleteThis @ic24.net> wrote:
 >
  > >Anyone have suggestions or problems resulting from the use of polyester
for
  > >the bulk of construction and epoxy to seal the polyester, say a 85
gm.glass
  > >woven cloth impregnated with epoxy .
  > >Only the cost saving would be large, considering the difference in the
price
  > >of the two resins.
  > >I have started on the frames of a 23 ft. WL. sailboat, strong back is in
  > >place.
  > >cheers
  > > Carl.
  > >
 ><!-- ~MESSAGE_AFTER~ -->
 >> Stay informed about: Polyester epoxy 

"AB" (alex.barker@virgin.net) writes:
 > Think of it this way:-
 > Polyester is a bonding resin, which means that it binds a material, I.E.
 > fibreglass by surrounding the fibres on both sides and through the fine
 > glass filaments. If you use it on ply then it cannot soak into the surface
 > and through to the other side to bind the plywood fibres.

Polyester does "soak into" the plywood, especially if given time by
lightening up on the catalyst and temperature. I've spread uncatalized
polyester resin on plywood and let it "soak in" before applying a second
layer with catalyst. I didn't put any fibreglass on the hull, just painted
over the cured polyester. Not scientific though. The small boat is only in
its second season so I'm not sure how successful it was yet. I've also
drilled lots of holes in wood to help polyester get a bite. I remember my
father doing the same thing when patching rust spots in an old car. I've
also done the same on the 14 year old car I have now.

I found the following reference in a book I read this afternoon
"How to Fibreglass Boats" by Ken Hanikson, published by Glen-L Marine in
1974 (Glen L Witt's company. Perahps email to Glen-L or Devlin would get
information they might have on the conditions under which polyester can be
succesfully used to cover a plywood boat.)

I found the above reference in "How to Beat the High Cost of Sailing" by
Richard Lyttle (1976). I also like "Frugal Yachting" by Larry Brown (1994)
although its not as informative. Brown sails a Potter 15 with his wife,
and the book is mostly about pocket cruisers that can be towed around on a
trailer. Since the original poster in this thread has already started to
build his boat these books are of limited interest, but I like them anyway
because they address the subject of sailing at least cost. Both books are
available from the Ottawa public library.


--
------------------------------------------------------------------------------
William R Watt National Capital FreeNet Ottawa's free community network
homepage: <a style='text-decoration: underline;' href="http://www.ncf.ca/~ag384/top.htm" target="_blank">www.ncf.ca/~ag384/top.htm</a>
warning: non-freenet email must have "notspam" in subject or it's returned<!-- ~MESSAGE_AFTER~ -->
 >> Stay informed about: Polyester epoxy